Treat your rusty ship, boat or marine vessel for iron and steel corrosion
VACTAN converts your ship or boat’s rust into a protective, blue-black metallo-organic complex and then provides a further layer of protection. VACTAN neutralises the corrosion process and protects marine metal surfaces by forming a film with low permeability to water vapour. One litre of VACTAN can treat up to 8-9 square meters of corroded surface.
- Self priming
- Minimal surface preparation
- Easy to apply
VACTAN Rust Converter is complex moisture of a vinyl acrylic copolymer and tannic acid for the treatment of corroded steel and iron surfaces.
VACTAN neutralises the corrosion process by converting the rust into a blue-black Metallo-organic complex which passivates the surface. It then further protects the surface by forming a film with low permeability to water vapour and oxygen. VACTAN Is self-priming but for long term protection, it is advisable to overcoat with suitable water or solvent-based mid coat or topcoat.
VACTAN is currently used by the following marine organisations: United States Navy, P&O Ferries, Disney Cruise Liners, Universal Studios amongst many others.
Trade / DIY benefits
- Self priming
- Minimal surface preparation
- Easy to apply
Trade / DIY applications
For use on all rusty marine steel and iron surfaces including:
- Ships
- Boats
- Container ships
- Sailing boats
- Yachts
- Canal boats
- Narrowboats
- Houseboats
- Cruise ships
- Tankers
- Warships
- Speedboats
- Historic marine vessels
- Fishing boats
- Tugboats
- Dredgers
- …and more
VACTAN can be used in the following marine areas:
- Canal boats and Narrowboats: Treat rust on hulls and floors.
- Barges: Treat rust on commercial barges.
- Hulls: Treat steel boat hulls for rust.
- Ships and ferries: Cargo ships and ferries rust treatment.
- Cruise ships: Rust conversion on cruise vessels.
- Engine bays: Treat rusty steel marine engine bays.
- Bilges: Treat interior bilge areas.
- Potable water tanks: Approved for use in portable/potable marine water tanks.
- Marine hardware: Rusty steel marine fittings.
- Boat trailers: Treat rusty boat trailers.
Coverage
One litre of VACTAN can treat up to 8-9 square metres of marine surface.
How to Step-by-Step
- Surfaces ready for treatment should be wire brushed to remove loose rust. It’s preferable to remove soluble salts by washing with water as they inhibit the conversion process. Rusty surfaces also need to be oil and grease free.
- VACTAN has been designed for application by spray and brush. With airless spray, a dry film thickness of up to 60 microns can be achieved without sagging. The addition of further water may be necessary for air assisted spraying. By brush application, a dry film thickness of 40 micros per coat is considered optimum.
- VACTAN can be applied over damp surfaces and dries quickly under suitable temperature and humidity conditions.
- Wash equipment immediately in water to remove all traces of VACTAN.
DRYING CONDITIONS
Temperature, humidity, air movement and film thickness all affect the time to reach the touch dry stage. Under ideal conditions, a 100 micron wet film of VACTAN will be touch dry in approximately 10 minutes at 20°C, whereas at 10°C and with little air movement this time can be as long as 2 hours. IMPORTANT: VACTAN should not be applied at temperatures below 10°C.
What you’ll need know
VACTAN is non flammable and can be regarded as essentially non hazardous under normal use. During use, gloves should be worn as VACTAN will stain the skin. Stains can be removed by first washing with diluted bleach then plenty of soap and water.
VACTAN should NOT be swallowed. If swallowed seek medical advice immediately.
WE ADVISE USERS OF THIS PRODUCT TO WEAR SAFETY GOGGLES, GLOVES AND SKIN SHOULD BE FULLY COVERED. CAREFULLY READ ALL APPLICATION AND SAFETY INSTRUCTION BEFORE USING
Ingestion: DO NOT induce vomiting, drink 1-2 glasses of water, seek medical attention
Skin Contact: Wash off immediately with plenty of soap and water, Remove
contaminated clothing, flush skin with running water. Seek medical attention if irritation or symptoms persist
Eye Contact: Rinse continuously with water for at least 15 minutes, holding the eyelids open. Seek medical attention. If can be done easily done remove contact lenses.
Spills/leaks: Absorb on inert absorbent and transfer to a container. Prevent spillage from entering natural waters/land drains.
FIRE: Use water fog or fine water spray. Emergency workers to wear full protective clothing including breathing apparatus.












